![will behringer xenyx q502usb work with tonor microphone will behringer xenyx q502usb work with tonor microphone](https://m.media-amazon.com/images/I/41tejshFy9L._AC_SL1000_.jpg)
- WILL BEHRINGER XENYX Q502USB WORK WITH TONOR MICROPHONE SOFTWARE
- WILL BEHRINGER XENYX Q502USB WORK WITH TONOR MICROPHONE TRIAL
- WILL BEHRINGER XENYX Q502USB WORK WITH TONOR MICROPHONE PC
- WILL BEHRINGER XENYX Q502USB WORK WITH TONOR MICROPHONE PROFESSIONAL
However If you turn it down to 50% so that there is no artificial boosting it is not noticeable. it also has an incredible annoying hiss when you amp it up to the maximum through your computer. I Personally do not prefer this on my buttons, as I tend to play with the knobs while recording, to get a feel of where the volume resides, without looking at it the actual mixer.Īs all Behringer Xenyx mixers do. Do not have a middle step to feel where the middle ground is.
WILL BEHRINGER XENYX Q502USB WORK WITH TONOR MICROPHONE PROFESSIONAL
not acceptable for serious professional use-cases.ĪLL the knobs that have to do with the volume: GAIN, LEVEL, COMPRESSION and MAIN.
![will behringer xenyx q502usb work with tonor microphone will behringer xenyx q502usb work with tonor microphone](https://m.media-amazon.com/images/I/61n0PO5oy+L._AC_SX679_.jpg)
The maximum bit rate is 16-bit in which it sends the signal to your device. I do not advice this mixer if you are looking to do some Voice-overs, audio productions or live audio mixing with it. including mirrored playback for 6mm jack Headphones, built-in 1 band compressor knob, and the ability to attach speakers for both L and R channels for playback Behringer Xenyx Q502USB 390 Mixer 1 XLR Mic Input with 15 V phantom power and compressor, 2-Band EQ and peak LED 2 Stereo Line inputs 2 Track In/Outs Master fader USB Audio Interface. Very compact all in one design for people who want to do entry level streaming-gaming sessions, sound boarding or instrumental jams.įor it's small size it does have a lot more features and options then you would expect from an USB interface for this price. I've seen so many YouTubers using expensive audio interfaces just to do vlogs, and having bought this Q502, I keep thinking.why did they waste their money - this will do exactly the same job, and at a fraction of the price.
WILL BEHRINGER XENYX Q502USB WORK WITH TONOR MICROPHONE PC
Secondly, the power switch.there isn't one! Dreadful design, otherwise I would have given it at least 4 starts for 'features.'Īll said, if you want a little mixer, which is sturdy, reliable and will give you some flexibility before you go into the PC or laptop, you won't find a better deal. (phantom power button is pressed down and the red light is on. What I currently have: I got the mixer plugged in via usb in my pc and the mic via XLR also in the mixer.
WILL BEHRINGER XENYX Q502USB WORK WITH TONOR MICROPHONE TRIAL
The 'MAIN MIX' pad I understand, but there is a designated phones pot, so I was scratching my head for a few minutes thinking 'why?' Again, can be a little confusing, but trial and error. As the title says, im using a Behringer XENYX Q502USB mixer and a Neewer NW-700 mic and get no microphone signal on my pc. If you have your mic on (there's phantom power too.nice touch!) coming through your cans, you will have the signal cut by pressing in the 'TO PHONES' pad. Firstly, there are a couple of pads that allow you to send both the RCA inputs and the USB input to both the phones and main mix, which I found slightly confusing at first.
![will behringer xenyx q502usb work with tonor microphone will behringer xenyx q502usb work with tonor microphone](https://linustechtips.com/uploads/monthly_11_2014/post-4616-0-46593000-1415272822.png)
However, I do have a couple of small issues. Installation doesn't present any problems, and the fact that it has a compressor (albeit basic) is fantastic.Īs you may expect from Behringer, this little mixer is robust and sounds fine for what I bought it for. It's compact so sits well next to my laptop allowing plenty of room for camera stand and speakers. Note that in all these cases the guitars will be irreversibly 'mixed', but you could record guitar and bass separately.I bought this Xenyx Q502 for my laptop and video calling, and it's great.
WILL BEHRINGER XENYX Q502USB WORK WITH TONOR MICROPHONE SOFTWARE
You may have to 'split' L and R on your software after the recording.
![will behringer xenyx q502usb work with tonor microphone will behringer xenyx q502usb work with tonor microphone](https://audioshopdubai.com/wp-content/uploads/2020/06/WhatsApp-Image-2020-06-10-at-6.56.30-PM.jpeg)
So the balances are a quick fix to separate the voice recording from the guitars when recording all of them at the same time. You are not able to map different channels on your mixer to different channels on your recording software. Microphone -> Input 1-Ģ) Using multiple Behringer inputs Behringer Here are crude diagrams of the setups: 1) Using Scarlett Behringer For smaller mixers with fewer inputs, the first diagram is valid. Of course that means you will only have mono recording, but that probably won't be an issue.ĮDIT A further point - I've just realised that the Q502 actually has up to 5 inputs! You don't need the Scarlett. You will then get microphone in one channel and guitars in the other, which can then be split into two separate tracks after recording should you want to process them separately. There is a workaround ( found here): pan one track to hard left and one track to hard right. It seems that the Behringer Xenyx USB mixers mix all tracks into one, so you won't have your microphone and guitars in separate tracks in your recording software (unless you record one track at a time).